1.1 Product Identifier Trade name GREENLOOP RUST CONVERTER N8 Product form Mixture UFI SXV3-81V2-600G-WNFA 1.2 Relevant Identified Uses of the Substance or Mixture and Uses Advised Against Relevant identified uses Professional and industrial conversion and stabilisation of rust on ferrous metal surfaces prior to coating or further treatment. Uses advised against Consumer use; application to non-ferrous metals or sensitive surfaces without compatibility testing; mixing with other chemical products. 1.3 Details of the Supplier of the Safety Data Sheet Manufactured for Greenloop Industries Ltd. Registered location London, United Kingdom Manufacturer VIAMAK Sp. z o.o. Address ul. Grzybowska 80/82/700, 00-844 Warsaw, Poland Email office@viamak.pl 1.4 Emergency Telephone Number Emergency telephone 112 (European emergency number). For medical advice, contact the competent national poison information centre in the country where the product is supplied. SECTION 2 — HAZARDS IDENTIFICATION 2.1 Classification of the Substance or Mixture Regulation (EC) No 1272/2008 (CLP/GHS): Hazard Class Category H-Statement Eye Irritation Category 2 H319 — Causes serious eye irritation 2.2 Label Elements Signal word WARNING Hazard statement H319 Causes serious eye irritation Precautionary statements P264 Wash hands thoroughly after handling. P280 Wear protective gloves and eye/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313 If eye irritation persists: Get medical advice/attention. 2.3 Other Hazards The mixture does not contain substances assessed as PBT or vPvB at concentrations of 0.1% or more. No component is identified as having endocrine-disrupting properties at 0.1% or more on the basis of available supplier information. Acidic product; prolonged skin contact may cause irritation. Spilled product may make floors slippery. SECTION 3 — COMPOSITION / INFORMATION ON INGREDIENTS 3.2 Mixtures Substance CAS No. EC No. Concentration (w/w) Classification (CLP) Citric acid, anhydrous 77-92-9 201-069-1 15–<20% Eye Irrit. 2, H319 Alkyl polyglucoside, C8–C10 68515-73-1 500-220-1 1–<3% Eye Dam. 1, H318; Skin Irrit. 2, H315 The full text of hazard statements is given in Section 16. Issued 03 August 2026 | Page 2

4.1 Description of First-Aid Measures General: Remove contaminated clothing. Seek medical advice if symptoms persist. Inhalation: Move to fresh air. Obtain medical advice if coughing or irritation occurs. Skin contact: Wash with plenty of water and soap. Remove contaminated clothing. Seek medical advice if irritation develops. Eye contact: Rinse cautiously with water for at least 15 minutes. Remove contact lenses if present and easy to do. Continue rinsing. Obtain medical advice if irritation persists. Ingestion: Rinse mouth. Do not induce vomiting. Give water in small amounts if conscious. Contact a poison centre or physician if unwell. 4.2 Most Important Symptoms and Effects, Both Acute and Delayed Eye irritation, redness, tearing and discomfort. Prolonged skin contact may cause redness or irritation. Ingestion may cause gastrointestinal discomfort. 4.3 Indication of Any Immediate Medical Attention and Special Treatment Needed Treat symptomatically. Eye exposure requires prompt and thorough irrigation. SECTION 5 — FIREFIGHTING MEASURES 5.1 Extinguishing Media Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide as appropriate for the surrounding fire. Do not use a direct high-pressure water jet. 5.2 Special Hazards Arising from the Mixture The product is water-based and not classified as flammable. Fire or severe heating may produce carbon monoxide, carbon dioxide and irritating fumes. 5.3 Advice for Firefighters Wear self-contained breathing apparatus and full protective equipment for significant fires. Cool exposed containers with water spray. SECTION 6 — ACCIDENTAL RELEASE MEASURES 6.1 Personal Precautions, Protective Equipment and Emergency Procedures Avoid contact with eyes and prolonged skin contact. Provide ventilation. Wear protective gloves and eye protection. Mark slippery areas. 6.2 Environmental Precautions Prevent large quantities from entering drains, soil or surface water. 6.3 Methods and Material for Containment and Cleaning Up Contain and absorb with sand, universal binder or other inert absorbent. Collect in a suitable labelled container. Wash residues with water while controlling discharge. 6.4 Reference to Other Sections See Sections 8 and 13. SECTION 7 — HANDLING AND STORAGE 7.1 Precautions for Safe Handling Avoid splashing and aerosol formation. Do not breathe spray mist. Avoid contact with eyes and prolonged skin contact. Do not eat, drink or smoke while handling. Do not mix with other chemicals. 7.2 Conditions for Safe Storage, Including Any Incompatibilities Store tightly closed in the original corrosion-resistant container at +5°C to +25°C. Protect from freezing, excessive heat, sunlight and contamination. Keep away from strong alkalis, oxidising agents and reactive metals. 7.3 Specific End Use(s) Professional and industrial rust conversion on ferrous metals. Follow the product label and operating instructions. Issued 03 August 2026 | Page 3

8.1 Control Parameters No Union occupational exposure limit has been established for the ingredients required to be disclosed. Observe applicable national workplace limits and supplier recommendations. 8.2 Exposure Controls Engineering controls: General ventilation. Local exhaust where spraying or mist formation is possible. Eye/face protection: Chemical splash goggles; face shield where splashing is likely. Hand protection: Chemical-resistant gloves, e.g. nitrile rubber. Select according to task and glove supplier data. Skin protection: Protective work clothing. Remove contaminated clothing and wash before reuse. Respiratory protection: Normally not required with adequate ventilation. For spraying or insufficient ventilation, use suitable particulate/mist protection. Environmental controls: Avoid uncontrolled release to drains, soil and surface water. SECTION 9 — PHYSICAL AND CHEMICAL PROPERTIES 9.1 Information on Basic Physical and Chemical Properties Property Value Physical state Liquid Colour Brown to dark brown Odour Mild, characteristic Melting/freezing point Not determined Boiling point / range Not determined Flammability Not classified as flammable Explosion limits Not applicable / not determined Flash point >93°C, closed cup Auto-ignition temperature Not determined Property Value Decomposition temperature Not determined pH 2.6–2.9 at 20°C; target approximately 2.7 Kinematic viscosity Not determined; dynamic viscosity typically 300–450 mPa·s at 20°C Solubility Miscible/dispersible with water Partition coefficient Not applicable to the mixture Vapour pressure Not determined Density / relative density 1.16–1.18 g/cm³ at 20°C Relative vapour density Not determined Particle characteristics Not applicable 9.2 Other Information VOC content: <50 g/L (calculated/estimated). Values should be confirmed by finished-batch quality-control testing where required. SECTION 10 — STABILITY AND REACTIVITY 10.1 Reactivity Acidic mixture. May react with strong alkalis and certain reactive metals. 10.2 Chemical Stability Stable under recommended storage and handling conditions. 10.3 Possibility of Hazardous Reactions Contact with strong alkalis may generate heat. Contact with reactive metals may release hydrogen. 10.4 Conditions to Avoid Freezing, excessive heat, contamination and prolonged exposure to air in open containers. 10.5 Incompatible Materials Strong alkalis, strong oxidising agents, hypochlorites and reactive metals. 10.6 Hazardous Decomposition Products Carbon monoxide, carbon dioxide and irritating fumes may form during fire or severe overheating. Issued 03 August 2026 | Page 4

11.1 Information on Hazard Classes as Defined in Regulation (EC) No 1272/2008 Acute toxicity: Not classified based on available component data and concentration calculations. Skin corrosion/irritation: Not classified; prolonged or repeated contact may cause irritation. Serious eye damage/irritation: Eye Irrit. 2 — causes serious eye irritation. Respiratory/skin sensitisation: Not classified based on available information. Mutagenicity: Not classified based on available information. Carcinogenicity: Not classified based on available information. Reproductive toxicity: Not classified based on available information. STOT single exposure: Not classified based on available information. STOT repeated exposure: Not classified based on available information. Aspiration hazard: Not classified. 11.2 Information on Other Hazards No mixture-specific toxicological test data are available. No component is known from available supplier information to have endocrine-disrupting properties at 0.1% or more. SECTION 12 — ECOLOGICAL INFORMATION 12.1 Toxicity The mixture is not classified as hazardous to the aquatic environment based on available ingredient data and concentrations. Avoid uncontrolled release. 12.2 Persistence and Degradability Organic components are expected to be biodegradable to varying degrees. No mixture-specific test data are available. 12.3 Bioaccumulative Potential Significant bioaccumulation is not expected for the principal components. 12.4 Mobility in Soil The product is water soluble/dispersible and may be mobile in soil. 12.5 Results of PBT and vPvB Assessment The mixture does not contain substances assessed as PBT or vPvB at 0.1% or more. 12.6 Endocrine Disrupting Properties No component is identified as endocrine disrupting at 0.1% or more based on available information. 12.7 Other Adverse Effects Large releases may lower the pH of water and adversely affect aquatic organisms. SECTION 13 — DISPOSAL CONSIDERATIONS 13.1 Waste Treatment Methods Minimise waste generation. Dispose of product residues and contaminated absorbents through an authorised waste contractor in accordance with local regulations. Do not discharge concentrated product to drains. Empty packaging should be drained and recycled or disposed of in accordance with local requirements. Waste classification must be determined by the waste producer according to use and contamination. Issued 03 August 2026 | Page 5